2025年1月18日 · Everything works flawlessly, including a VPN that automatically connects to my home network before routing to the internet. I followed this OpenVPN guide, and overall, the setup works great—except for one issue. When I connect my 4G modem, all connectivity is lost. If I disable the VPN kill-switch and restart, the 4G modem works fine again.

2024年12月13日 · Folks, On my home network, I have three VLAN: LAN WAN IOT Recently, I stumbled upon a site that did not allow overseas login from US. So, I used a friends VPN to complete my obligation. Also, the current popular streamers have different contents for different GEO and we are all now global folks and enjoy talking about episodes. Having a VPN will allow me access to content meant for the ...

2020年5月25日 · I have a TP-Link Archer C7 1.1 which I am using OpenWRT 19.07 RC2 on. It connects to my existing network via the ‘internet’ (IWLAN) port and is setup to connect to a VPN (using OpenVPN), which is active on the wifi and LAN ports.

2025年2月3日 · I have 1- Wireguard server running on a remote TP-Link, OpenWRT router and 2- Wireguard client running on my local TP-Link, OpenWRT router. They seem to be communicating because keep-alive packets are being sent by client and received and registered at both ends. But I cannot get any traffic to go through the VPN tunnel. With OpenVPN as soon as the VPN is enabled all traffic is directed ...

2025年1月29日 · I'm having a really hard time getting the following to work: Problem 1. I cannot get 2 wireguard vpns running at the same time. Problem 2. I cannot get lan -> vpn1 and wlan -> vpn2 It should not be that difficult, but apparently I'm a moron, I could really use the help. EDIT: Finally managed to get both VPNs working on the router itself. I see TX/RX counters increase and can ping the WireGuard ...

2025年2月3日 · I setup my router to use a vpn via wireguard . It works . So I soon discovered that Amazon Prime Video is unhappy with my vpn . This is not unusual it seems . So research indicates I can setup PBR to route specific ips out the wan interface instead of the wg interface .

2025年2月3日 · So I read these forum posts: Transmission torrent client through VPN - #19 by nidstigator and Bind Transmission to VPN using VPN Policy-Based Routing - #2 by vgaetera Its a bit dated, but I could follow what was going on and its still relevant afaict. I understand that with running Transmission over OpenVPN you need to compensate for the changing ip-address of OpenVPN. However the one bit that ...

2025年1月21日 · I am trying to access a VLAN on the Wireguard VPN server from the Wireguard client. I can access the VPN Server lan IPs and the VLAN gateway, but I am unable to access the VLAN IPs. Anyone have any ideals? Thanks in advance.

2025年1月26日 · i have 2 sites, A - netgear wax206, openwrt (domain .lan) B - gl.inet mt-6000, openwrt (domain .lan) i need to access some servers from site B to site A (not so much the other way around) i have wireguard set up on both routers, and wg clients on some machines i use on site B to access site A one of the use cases for site A is it runs a storage backup server, so i want to rsync data there ...

2025年1月6日 · Hi everyone, I would like to configure an OpenVPN client on OpenWrt so that it is in action only when I request resources from the other LAN. Example: Office - OpenVPN Server with RDP Server Home - OpenVPN Client I would like that when I am surfing the Internet from home, it does not pass traffic from the VPN, while if I want to connect to the Server via RDP it does. Following the Wiki ...